• Support,
  • Installation

The installation of the tracks is initially the same for the LightLight and Sense System. However, please note the instructions when connecting the Buschfeld light track.

88104_631

Fix the cable suspension system on the ceiling, spacing between the cables 2000 mm maximum. Cable suspension 250 mm max. from the end of the track.
 

88104_632

Bring all wire rope holders to the desired height, align them with a laser spirit level. Secure heavy control gear such as Cube, Bigbox and Bigbox48 (at track level) with an additional rope suspension. Insert the wire rope holder into the upper rail channel and screw in place.

Align the tracks with a spirit level and readjust the rope lengths on the wire rope holder if necessary. Place protruding rope ends in the upper rail channel or cut to length. 

Installation to be carried out by qualified personnale only! Disconnect the system!

88104_635

Lighting tracks Sense System or LightLight:
When connecting the power feed and the control gear, the + / - polarity must be observed!
+ Brass inner conductor of the track
- track itself
The polarity is usually also marked with a sticker on the power feed.

88104_636

Shorten the feeder rods
1st Length L2 = upper edge of track to the round end of the plug, L1 + 5 mm (tolerance +0/-1 mm)
2nd trim carefully (taper) so as not to damage the contact inter- faces in the connectors 
3rd connect the feeder rod and the plug by pushing the coupling bushing upwards

Installation to be carried out by qualified personnale only! Disconnect the system!

88104_637

Lighting tracks Sense System or LightLight:
When connecting the power feed and the control gear, the + / - polarity must be observed!
+ Brass inner conductor of the track
- track itself
The polarity is usually also marked with a sticker on the power feed.

88104_638

Use only stranded cables with wire end sleeves in the screw contacts of the pendant track. No rigid lines! Please note the marking (+) for the connection of the live conductor.

Installation to be carried out by qualified personnale only! Disconnect the system!

88104_639

Secure heavy control gear (A) such as Cube, Bigbox and Bigbox48 in the designer housing (on track level) for visible mounting with an additional cable suspension (D). Insert the cord holder into the upper track channel and screw in place.

88104_640

Remove the design housing carefully from the base plate, turn the locking bolts (E) on the side of the adapter to 90°. One adapter has a golden contact pin (B), this adapter must be in contact with the inner conductor of the track. If necessary, turn the base plate by 180 °.

88104_641

Insert both adapters into the rail channel, pressing firmly into the track; turn back the side latches (E) of the adapter by 90 °. Establish a connection on the primary side. With Bigbox, plug the earth cable onto the earth lug on the housing cover.

88104_642

Carefully put on the housing cover, to do this, gently press all springs together and slide the housing (G) on.

Installation to be carried out by qualified personnale only! Disconnect the system!

88104_643

Secure heavy control gear (A) such as Cube, Bigbox and Bigbox48 in the designer housing (on track level) for visible mounting with an additional cable suspension (D). Insert the cord holder into the upper track channel and screw in place. Pay attention to the position of the Led Line in the upper track channel. Remove the design housing carefully from the base plate, turn the locking bolts (E) on the side of the adapter to 90°. One adapter has a golden contact pin (B), this adapter must be in contact with the inner conductor of the track. If necessary, turn the base plate by 180 °.

88104_644

Insert both adapters into the track channel, pressing firmly into the track. Turn back the side latches (E) of the adapter by 90 °. Connect the strands for the Led Line (C) to the base plate of the control gear at the intended location. The strands can be led between the plastic housing and the clamping brackets (F).

88104_645
88104_651

Slide the electrical connector (A) onto the inner conductor of the first section of track. 
Insert the mechanical connector (B) into the track, as indicated, and screw firmly into place.

Attention! Make sure you tighten the screws by turning them in the right direction! The countersunk screws in connector are screwed into place by turning them in an anti-clockwise direction and press from the inside into the profile of the track.

Connector part (C) is intended for the upper channel (only necessary for pendant tracks), to tighten the threaded pins in connector part (C) are screwed clockwise inwards. Also note the screw direction here!

88104_652

Press the sections of track together. Screw the other side of the track into place.

Attention! Make sure you tighten the screws by turning them in the right direction! The countersunk screws in connector are screwed into place by turning them in an anti-clockwise direction and press from the inside into the profile of the track.